GraphiteHub

Anode coating materials, and the know-how to use them

We supply anode coating materials through a close partnership with a market-leading producer, test graphite from ore or coke through to the battery cell, and source natural graphite.

Anode coating pitch

Coating material is a refined, petroleum-based pitch. Heated onto graphite, it leaves a thin carbon shell around every particle. On synthetic graphite it is also the binder that holds fine particles together before graphitisation.

It is a small share of anode cost, often under a tenth, but it sets much of how the anode performs. We have a long-standing, close partnership with a market-leading producer, whose materials are validated by the leading anode makers, and act as its technical and commercial link to producers outside China.

Faster chargingA smooth carbon surface lets lithium move in and out more easily.
Longer cycle lifeThe shell limits side reactions with the electrolyte.
First-cycle efficiencyLower surface area means less lithium is lost in the first charge.
Cold and safetyBetter low-temperature performance and a more stable surface.
Product range

Solid coating pitch

High softening point pitch in low to high temperature grades, milled to your particle size, that coats graphite with a thin carbon shell.

Used for
Natural and synthetic graphite anodes
Improves
First-cycle efficiency, cycle life and fast charging

Liquid coating

A liquid coating route that lays an even, very thin carbon layer on fine particles.

Used for
Fast-charging and fine-particle anodes
Improves
Rate performance and coating evenness

Granulation binder

Binder pitch that bonds fine synthetic particles together before graphitisation, and can coat them again after it.

Used for
Synthetic graphite anodes
Improves
Fast charging and lower swelling

Custom formulations

Resin-modified and blended grades built around your graphite, your furnace and your customers.

Used for
Specific furnaces and customer specifications
Improves
Fit to your process and faster qualification

Next-generation coatings

Coating and binder materials for newer anode and cathode materials beyond graphite.

Used for
Silicon-carbon, hard carbon and LFP
Improves
Cycle life and first-cycle efficiency

What coating changes

Across our coating evaluations the same pattern shows up when graphite is coated, carbonised and tested in coin cells. Exact results depend on the graphite and the process.

Uncoated graphite particles under the electron microscope, with rough, grooved surfaces
Before coating · rough, grooved
Surface areaLower
First-cycle efficiencyHigher
Capacity at fast chargeMuch higher
Capacity kept over many cyclesHigher
Capacity at slow chargeAbout the same
Coated graphite particles under the electron microscope, with smoother surfaces
After coating · smoother, sealed

What we look for in a coating material

Softening pointMust match the customer's mixing and heating process, which is why a full range matters.
Coking valueHow much carbon is left after heating. Higher means a fuller shell from less material.
Quinoline insolublesFine solids in the pitch. Too many and the coating goes on unevenly.
Ash and metalsImpurities that cause side reactions in the cell. Kept low and stable by multi-stage demagnetisation.
ConsistencyBatch-to-batch stability, so the anode line does not need requalifying with every delivery.

Research and development behind every grade

Coating materials are not a commodity. The right result depends on the graphite, the process and the cell it is going into. That is where our technical depth comes in.

Working as one teamWe work hand in hand with the producer's own research institute, R&D centres and pilot testing base, so trials and custom grades move quickly.
Roots in industrialisationOur technical leads come from one of China's original carbon research institutes and worked on the early scale-up of synthetic graphite anode.
Built and ran anode linesEngineers who have designed, built and operated commercial anode material lines, so advice is grounded in production.
Matching the materialWe screen structure, impurities, graphitisation behaviour and surface response to choose the right coating or granulation route.
Custom developmentResin-modified and blended formulations for adhesion and fast charging, developed with the customer in the lab.
Knows what buyers testYears of joint work with leading anode makers, so we know their specifications, failure modes and qualification steps.

Testing and validation

We test materials the way an anode maker will, so the results stand up in front of customers, lenders and investors. Run the whole chain or only the stages you need.

Ore to coated anode with what is tested at each step
Step 1OreGrade, impurities, mineralogy
Step 2FlotationConcentrate grade and yield
Step 3SpheronisingParticle size, tap density, yield
Step 4PurificationPurity, metals, surface area
Step 5CoatingCoating and carbonisation
Step 6Coin cellCapacity, efficiency, rate, cycle life
One-step route single particles, the lower-cost route used widely in energy storage
Step 1Coke and pitchCoke structure, pitch screening
Step 2CrushingParticle size
Step 3CarbonisationVolatiles, sulphur
Step 4GraphitisationXRD, Raman, density, BET, SEM
Step 5Pitch coatingCoating agent and process window
Step 6Carbonise and sieveSize and stability
Step 7Coin cellElectrochemical and physical data
Two-step route fine particles granulated into larger ones and coated again, for fast-charging EV grades
Step 1Coke and binderCoke structure, binder screening
Step 2CrushingParticle size, SEM
Step 3GranulationBinder choice, particle size
Step 4CarbonisationVolatiles, sulphur
Step 5GraphitisationXRD, Raman, density, BET, SEM
Step 6Second coatingCoating agent and process window
Step 7Coin cellElectrochemical and physical data

Uses our coating materialsEvery step can be tested

What gets measured
Particle sizeTap and pressed densitySurface area (BET)XRDRamanSEMMetals (ICP)First-cycle efficiencyRate capabilityCycle retention

Work runs from lab screening through pilot runs to industrial volumes, depending on whether the goal is a first look, due diligence or customer qualification. The output is a full data package with a recommended process route, not just samples.

Coin cells are the first screen. Customers qualify a material in full cells over about 1,000 cycles, which can take 6 to 12 months, so we set up tests to match what they will check.

Beyond graphite anodes

Coating is not only for graphite. We also supply coating and binder materials for the next generation of battery materials.

Silicon-carbonHard carbonLFP and other cathodes
BatteryLithium-ion anodeSodium-ion anodeLithium-ion cathode
What the coating doesForms the carbon shell and matrix that hold swelling silicon together.Closes an open, porous surface so less sodium is lost in the first charge.Adds a thin conductive carbon layer around each cathode particle.
Main gainLonger cycle lifeHigher first-cycle efficiencyFaster charge and discharge
Silicon-carbonLithium-ion anode

Forms the carbon shell and matrix that hold swelling silicon together.

Longer cycle life
Hard carbonSodium-ion anode

Closes an open, porous surface so less sodium is lost in the first charge.

Higher first-cycle efficiency
LFP and other cathodesLithium-ion cathode

Adds a thin conductive carbon layer around each cathode particle.

Faster charge and discharge

Sourcing

Through our network across producing regions, we source natural flake graphite, feedstock for synthetic graphite and related carbon materials. We know the suppliers, and can test material before it ships.

Natural flake concentrateLarge flake through to fines, for anode, refractory, expandable and other uses.
Synthetic feedstockPetroleum coke and needle coke for synthetic graphite and anode producers.
Checked before you commitSampling and testing, tied into our validation work when needed.
Carbon fibre insulationOn request, pitch-based carbon fibre felt and board for high-temperature furnaces, such as those used in optical fibre and semiconductor production.

Anode coating questions

Short answers on coating pitch, testing and samples. For anything specific to your material, talk to our technical team.

Why work with GraphiteHub?

We work in close partnership with a market-leading producer whose materials are validated by the leading anode makers. You get proven grades, testing on your own graphite, and one team handling specifications, documents and shipping.

What is anode coating pitch?

A refined, high softening point pitch that is mixed with graphite and heated until it forms a thin, even carbon layer on each particle. That layer seals the surface, so the anode loses less lithium in the first cycle, lasts longer and charges faster.

Why do graphite anodes need a coating?

Uncoated spherical graphite has rough, open edges that react with the electrolyte. Coating smooths and seals those edges, which raises first-cycle efficiency, improves cycle life and fast charging, and makes the material safer in the cell. It is a small share of anode cost with a large effect on performance.

Which coating material suits my graphite?

It depends on the graphite and the process. Natural and synthetic graphite, particle size and surface area, and your furnace conditions all change the grade that works best. We match softening point, coking value, quinoline insolubles and ash to your material, then prove it in tests.

Do you supply coating materials beyond graphite anodes?

Yes. As well as grades for natural and synthetic graphite, we supply coating and binder materials for silicon-carbon anodes, hard carbon for sodium-ion batteries and carbon-coated cathodes such as lithium iron phosphate.

Do Chinese export controls affect coating materials?

Coating pitch is not on the Chinese export control list today. Graphite and some coating technology are controlled, or under controls that are currently paused.

How do you test a coating material?

We coat your graphite in the lab, carbonise it and build coin cells to measure capacity, first-cycle efficiency and rate performance, alongside particle size, surface area, tap density and purity. Promising results move to pilot runs and full-cell work.

How do I get samples or start test work?

Get in touch with your graphite type, target specifications and volumes. We will recommend grades, send samples and set up a test plan that matches how your customers qualify material.

Request samples or a technical call

Tell us about your graphite and your process, and we will recommend materials and arrange a call.

Get in touch